반응형
AMI BIOS signals (American Megatrends Inc)
AMI BIOS 신호(또는 비프음 코드)는 아래와 같습니다. 그러나 이러한 유형의 BIOS를 사용하여 컴퓨터를 생산하는 다양한 제조업체로 인해 경고음 코드가 다를 수 있습니다.
사운드 신호(비프음 코드)설명
1 short beep | No errors detected, normal boot |
2 short beeps | Parity circuit failure |
3 shot beeps | Base 64 K RAM failure (The first 64 KB of RAM are out of order) |
4 short beeps | System timer failure |
5 short beeps | Process failure |
6 short beeps | Keyboard controller Gate A20 error |
7 short beeps | Virtual mode exception error (System board issue) |
8 short beeps | Display memory Read/Write test failure (VRAM error) |
9 short beeps | ROM BIOS checksum failure |
10 short beeps | CMOS shutdown Read/Write error |
11 short beeps | Cache Memory error |
1 long beep, 3 short beeps | Conventional/Extended memory failure (Graphics card is out of order) |
1 long beep, 8 short beeps | Display/Retrace test failed |
Two-tone siren | Low CPU Fan speed, Voltage Level issue. |
AWARD BIOS signals
아래에는 AWARD BIOS 신호(비프음 코드)가 나열되어 있습니다. 이전의 경우와 마찬가지로 경고음 코드는 이러한 유형의 BIOS로 컴퓨터를 생산하는 다양한 제조업체로 인해 다를 수 있습니다.
사운드 신호(비프음 코드)설명
1 long beep, 2 short beeps | Indicates a video error has occurred and the BIOS cannot initialize the video screen to display any additional information. (Graphics card not found, or VRAM error) |
1 long beep, 3 short beeps | Video card not detected (reseat video card) or bad video card (Depending on the BIOS version, this beep code may indicate either a graphics card error or a keyboard error) |
Endlessly repeated signal | RAM problem. |
Repeated frequent beeps while the computer is working | Overheating processor (CPU) |
Repeated beeps, frequent and seldom | Issue with the processor (CPU), possibly damaged |
다른 하드웨어 문제가 있는 경우 BIOS에서 해당 메시지를 표시합니다.
Dell signals
사운드 신호(비프음 코드)설명
1 beep | BIOS ROM corruption or failure |
2 beep | Memory (RAM) not detected |
3 beep | Motherboard failure |
4 beep | Memory (RAM) failure |
5 beep | CMOS Battery failure |
6 beep | Video card failure |
7 beep | Bad processor (CPU |
For other Dell signals, you can visit this page.
IBM BIOS signals
다음은 IBM BIOS 신호입니다.
사운드 신호(비프음 코드)설명
None | No Power, Loose Card, or Short (Power supply unit, motherboard or internal speaker is out of order) |
1 short beep | Normal POST, computer is ok. (No errors detected) |
2 short beeps | POST error, review screen for error code. |
Continuous beeps | No Power, Loose Card, or Short. (No power supply) |
Repeated short beep | No Power, Loose Card, or Short. (No power supply) |
1 long beep, 1 short beep | Motherboard issue. |
1 long beep, 2 short beeps | Video (Mono/CGA Display Circuitry) issue. |
1 long beep, 3 short beeps | Video (EGA) Display Circuitry. |
3 long beeps | Keyboard or Keyboard card error. |
1 beep and black screen | Video Display Circuitry. (The monitor doesn’t work) |
Phoenix BIOS signals
아래에는 Phoenix BIOS Q3.07 또는 4.X 신호(비프음 코드)가 나열되어 있습니다.
사운드 신호(비프음 코드)설명
1-1-1-1 | Unconfirmed beep code. Reseat RAM chips or replace RAM chips as possible solution |
1-1-1-3 | Verify Real Mode. |
1-1-2-1 | Get CPU Type. |
1-1-2-3 | Initialize system hardware. |
1-1-3-1 | Initialize chipset registers with initial POST values. |
1-1-3-2 | Set in POST flag. |
1-1-3-3 | Initialize CPU registers. |
1-1-4-1 | Initialize cache to initial POST values. |
1-1-4-3 | Initialize I/O. |
1-2-1-1 | Initialize Power Management. |
1-2-1-2 | Load alternate registers with initial POST values. |
1-2-1-3 | Jump to UserPatch0. |
1-2-2-1 | Initialize keyboard controller. |
1-2-2-3 | BIOS ROM checksum. |
1-2-3-1 | 8254 timer initialization. |
1-2-3-3 | 8237 DMA controller initialization. |
1-2-4-1 | Reset Programmable Interrupt Controller. |
1-3-1-1 | Test DRAM refresh. |
1-3-1-3 | Test 8742 Keyboard Controller. |
1-3-2-1 | Set ES segment to register to 4 GB. |
1-3-3-1 | 28 Autosize DRAM. |
1-3-3-3 | Clear 512 K base RAM. |
1-3-4-1 | Test 512 base address lines. |
1-3-4-3 | Test 512 K base memory |
1-4-1-3 | Test CPU bus-clock frequency. |
1-4-2-4 | Reinitialize the chipset. |
1-4-3-1 | Shadow system BIOS ROM. |
1-4-3-2 | Reinitialize the cache. |
1-4-3-3 | Autosize cache. |
1-4-4-1 | Configure advanced chipset registers. |
1-4-4-2 | Load alternate registers with CMOS values. |
2-1-1-1 | Set Initial CPU speed. |
2-1-1-3 | Initialize interrupt vectors. |
2-1-2-1 | Initialize BIOS interrupts. |
2-1-2-3 | Check ROM Copyright notice. |
2-1-2-4 | Initialize manager for PCI Options ROMs. |
2-1-3-1 | Check video configuration against CMOS. |
2-1-3-2 | Initialize PCI bus and devices. |
2-1-3-3 | Initialize all video adapters in system. |
2-1-4-1 | Shadow video BIOS ROM. |
2-1-4-3 | Display Copyright notice. |
2-2-1-1 | Display CPU Type and speed. |
2-2-1-3 | Test keyboard. |
2-2-2-1 | Set key click if enabled. |
2-2-2-3 | 56 Enable keyboard. |
2-2-3-1 | Test for unexpected interrupts. |
2-2-3-3 | Display prompt Press F2 to enter SETUP. |
2-2-4-1 | Test RAM between 512 and 640 k. |
2-3-1-1 | Test expanded memory. |
2-3-1-3 | Test extended memory address lines. (Test extended memory address lines). |
2-3-2-1 | Jump to UserPatch1. (Jump to UserPatch1). |
2-3-2-3 | Configure advanced cache registers. |
2-3-3-1 | Enable external and CPU caches. |
2-3-3-3 | Display external cache size |
2-3-4-1 | Display shadow message. |
2-3-4-3 | Display non-disposable segments. |
2-4-1-1 | Display error messages. |
2-4-1-3 | Check for configuration errors. |
2-4-2-1 | Test real-time clock. |
2-4-2-3 | Check for keyboard errors |
2-4-4-1 | Set up hardware interrupts vectors. |
2-4-4-3 | Test coprocessor if present. |
3-1-1-1 | Disable onboard I/O ports. |
3-1-1-3 | Detect and install external RS232 ports. |
3-1-2-1 | Detect and install external parallel ports. |
3-1-2-3 | Re-initialize onboard I/O ports. |
3-1-3-1 | Initialize BIOS Data Area. |
3-1-3-3 | Initialize Extended BIOS Data Area. |
3-1-4-1 | Initialize floppy controller. |
3-2-1-1 | Initialize hard disk controller. |
3-2-1-2 | Initialize local bus hard disk controller. |
3-2-1-3 | Jump to UserPatch2 |
3-2-2-1 | Disable A20 address line. |
3-2-2-3 | Clear huge ES segment register. |
3-2-3-1 | Search for option ROMs. |
3-2-3-3 | Shadow option ROMs. |
3-2-4-1 | Set up Power Management. |
3-2-4-3 | Enable hardware interrupts. |
3-3-1-1 | Set time of day. |
3-3-1-3 | Check key lock. |
3-3-3-1 | Erase F2 prompt. |
3-3-3-3 | Scan for F2 key stroke. |
3-3-4-1 | Enter SETUP. |
3-3-4-3 | Clear in POST flag. |
3-4-1-1 | Erase F2 prompt. |
3-4-1-3 | POST done, prepare to boot operating system. |
3-4-2-3 | Check password (optional). |
3-4-3-1 | Clear global descriptor table. |
3-4-4-1 | Clear parity checkers. |
3-4-4-3 | Clear screen (optional). |
3-4-4-4 | Check virus and backup reminders. |
4-1-1-1 | Try to boot with INT 19. |
4-2-1-1 | Interrupt handler error. |
4-2-1-3 | Unknown interrupt error. |
4-2-2-1 | Pending interrupt error. |
4-2-2-3 | Initialize option ROM error. |
4-2-3-1 | Shutdown error. |
4-2-3-3 | Extended Block Move. |
4-2-4-1 | Shutdown 10 error. |
4-3-1-3 | Initialize the chipset. |
4-3-1-4 | Initialize refresh counter. |
4-3-2-1 | Check for Forced Flash. |
4-3-2-2 | Check HW status of ROM. |
4-3-2-3 | BIOS ROM is OK. |
4-3-2-4 | Do a complete RAM test. |
4-3-3-1 | Do OEM initialization. |
4-3-3-2 | Initialize interrupt controller. |
4-3-3-3 | Read in bootstrap code. |
4-3-3-4 | Initialize all vectors. |
4-3-4-1 | Boot the Flash program. |
4-3-4-2 | Initialize the boot device. |
4-3-4-3 | Boot code was read OK. |
Двух тоновая сирена | Low CPU Fan speed, Voltage Level issue. |
출처 : https://hetmanrecovery.com/recovery_news/bios-audio-signals.htm#plan_1
반응형
'백과사전' 카테고리의 다른 글
사람의 뇌는 부정의 개념을 이해 못해요. (0) | 2022.12.27 |
---|---|
부산에 왔다면 꼭 먹어야 하는 음식 BEST (0) | 2022.12.07 |
우회전 일시정지 2022년 10월 12일부터 단속 시행 (0) | 2022.10.13 |
반야심경 - 현대어 번역 (0) | 2022.09.14 |
크롬 스크롤링 느리게 스무스하게 내려갈때 해결방법 ! (로지텍 추가) (3) | 2022.06.14 |